亚博足彩

设为亚博足彩    收藏本站

保定华庆钢模具厂
      产品列表
水泥件模具
隔离带钢模具
检查井钢模具
标志桩钢模具
化粪池钢模具
井盖模具
围墙板钢模具
方涵模具
流水槽钢模具
声屏障钢模具
      资质荣誉
      联系我们
保定华庆钢模具厂
地 址:保定市东城工业区
电 话:18831266588
联系人:边经理
传 真:0312-8103818
在线QQ:107108222@qq.com
行业新闻

简述高铁护栏模板的使用规范

高铁护栏模板亚博足彩采用的面板厚度是与防撞护栏预制块的长度有关系的,生产这种钢模具需要构造图或者大样图,保证正确性。高铁护栏模板,高速护栏模板,防护栏模板厂家是隔离墩模具的另一种生产形式,按照防撞护栏钢模具的生产标准来说,在1.5米以下的通常使用标准3毫米的钢板,长度在1.5米以上的使用的钢板厚度需要达到标准4个厚,这样才能保证在现场浇筑的过程中模具不会发生变形。这种钢模具都是论重量卖的,看需要的模具数量。

The thickness of the panel used for the high-speed rail formwork is related to the length of the prefabricated block of the anti-collision guardrail. The production of this steel mold requires the structural drawing or detailed drawing to ensure the correctness. The anti-collision guardrail formwork mold is another production form of the isolation pier mold. According to the production standard of the anti-collision guardrail steel mold, the standard 3mm steel plate is usually used below 1.5m, and the thickness of the steel plate used above 1.5m needs to reach the standard 4 thicknesses, so as to ensure that the mold will not deform in the process of on-site pouring. This kind of steel mould is sold by weight, depending on the quantity of mould needed.

GAOTIEHULANMOBANDEJUTISHIYONGGUIFANRUXIA:1.MOJUDIBUHEDINGBUDOUMEIYOUGANGBAN,YOUSHUGENLAGANLIANJIEERCHENG,YONGYUXIANJIAOSHENGCHAN,YIDANJIAOZHUHUNNINGTUJIUWUFAZAICIYIDONG,SUOYISHIYONGQIANBIXUBAMOJUFANGDAOHESHIDEWEIZHIRANHOUSHUASHANGJIYOU;2.DIAOJIEGONGLUHULANMOJUDELAGANSHIMOJUDEKUANDUBAOCHIYIZHI,NINGJINXIANGLINMOJUJIANDELUOSHUAN,JIANCHAGEJIEMOJUJIANMEIYOULIUYOUFENGXI,FOUZEYIDANLOUJIANGHUIYINGXIANGGONGLUHULANZHILIANG;3.SHIYONGGUANDAOJIANGJIAOBANHAODEHUNNINGTUZHURUMOJU,BINGSHIYONGZHENDONGBANGJIANGQIPAOZHENCHU,RANHOUJIGUANWANJIANGDEMOJUFUSHANGYICENGSULIAOBOMO,LAIBAOZHENGGONGLUHULANDENAIYONGHEMEIGUAN;4.8GEXIAOSHIHOUJIEQUSULIAOBOMO,DAKAIMOJUZUOYOUDUANDELUOSHUAN,CHAIQUMOJU,RANHOUDENGDAIHUNNINGTUHULANZIRANFENGGANJIKE,CHAIXIALAIDEMOJUJIUKEYIJINXINGXIAYIDUANGONGLUHULANDEJIAOZHULE。

The specific specifications for the use of high-speed rail formwork are as follows: 1. There is no steel plate at the bottom and top of the formwork, which is connected by several pull rods and used for cast-in-place production. Once the concrete is poured, it can not be moved again, so before use, the formwork must be placed in a proper position and painted with engine oil; 2. Adjust the pull rods of the highway guardrail formwork to keep the width of the formwork consistent, and tighten the Bolt, check that there is no gap between the molds of each section, otherwise the leakage of slurry will affect the quality of highway guardrail; 3. Use the pipe to inject the mixed concrete into the mold, and use the vibrator to shake out the bubbles, and then cover the poured mold with a layer of plastic film to ensure the durability and beauty of highway guardrail; 4.8 hours later, remove the plastic film, open the bolts at the left and right ends of the mold Bolt, remove the mold, and then wait for the natural air drying of the concrete guardrail. The removed mold can be used for the next section of highway guardrail pouring.


【上一个】 防撞墙模板生产的四个步骤 【下一个】 公路防护栏模板如何应用


 · 简述高铁护栏模板的使用规范

隔离墩模具-水泥隔离墩模具-高速隔离墩模具—保定华庆钢模具厂 |防撞墙模具|沟盖板模具|流水槽钢模具|检查井钢模具|检查井模具|标志桩模具|隔离墩模具|化粪池模具|塑料盖板模具|水泥防撞墙模具|